Ikelite onderwaterhuis voor Sony A1 en A7S III #71476

Deze onderwaterbehuizing heeft de toevoeging van een compatibele DL-lenspoort nodig (niet inbegrepen).
 Bekijk hier de lijst met compatibele poorten.

Vacuümtesten
Aan de zijkant van de behuizing is standaard een vacuümklep gemonteerd. De vacuümklep is ontworpen met een laag profiel om interferentie met bedieningselementen te voorkomen. Met de optionele vacuümpomp met meter # 47011 kunt u vacuüm trekken op de behuizing om te controleren op lekken voordat u het water ingaat.

Het vacuüm trekken op het systeem zorgt ook voor extra veiligheid aan het wateroppervlak, vooral belangrijk bij gebruik van de behuizing in ruwe branding.

M16 Accessory Port
The spare M16 threaded accessory port provides an attachment point for third party accessories including HDMI bulkheads.

TTL Exposure
This housings supports your choice of shooting with manual strobe exposure or adding a TTL converter depending on your application. The flash bulkhead is located on the top of the case to alleviate strain on the sync cord.

You can enjoy the fastest and most accurate TTL exposure on the market by adding the DL2 DS Link Sony TTL Converter Ikelite ST1 Hotshoe Kit # 46042 and a compatible Ikelite DS strobe. Exposure compensation can be used added or subtracted in the camera.

Viewfinders
The included SuperEye Viewfinder provides an enhanced view of the camera's electronic viewfinder when viewed through a dive mask. The viewfinder removes quickly and easily for the attachment of an optional Straight Magnified Viewfinder # 6890.2 or 45° Magnified Viewfinder (Type 1) # 6891.1.

Ikelite DS Strobe Compatibility
Any Ikelite DS strobe may be used in manual exposure modes by attaching one or two with a compatible electrical sync cord. Current model DS strobes may be used in TTL exposure mode by adding the optional DL2 DS Link TTL Converter and an electrical sync cord.

Non-Ikelite Strobe Compatibility
SEA&SEA, INON, and Retra strobes with an electrical connection can be triggered in manual exposure modes using an electrical sync cord. Strobes without an electrical sync cord connection cannot be attached to this system unless slaved off of a hard-wired strobe.

Ikelite Non-Digital Strobe Compatibility
Older non-digital strobes featuring an ICS-5 electrical sync cord bulkhead can be used with this system in manual exposure modes.

Fiber Optic Compatibility
Fiber optic only strobes are not compatible with this installation. An external strobe must be connected by electrical sync cord.

Remote Triggering Compatibility
Strobes with remote slave capabilities may be triggered off of a flash attached to the housing by electrical sync cord. Ikelite DS strobes support remote triggering using the Optical Slave Converter # 4405 or the Water Wizard system (manufactured and sold by Aquatica).

Specifications

-200' (60m) depth rating
-Compatible with DL system lens ports
-Controls for all camera functions except: Diopter adjustment, Focus mode dial (a1); Joystick up/down/left/right (Joystick can be depressed), Control wheel; Control wheel functions may be accessed using the Front and Rear Dials
-1/4-20 thread base mounts with 3.5" spacing
-Slightly positive buoyancy in fresh water
-Actual buoyancy varies depending on choice of lens and port
-Housing weight: 4.67 lb (2121 g)
-Weight tray with left handle 11 oz (312 g)
-Sizes:  9 x 7.25 x 6" (229 x 184 x 152 mm) Not including
-Vacuum valve included (pump sold separately)
-Included Ikelite ICS-5 bulkhead connector with manual hotshoe for reliable electrical triggering of underwater strobes; Optional TTL accessories provides automatic exposure with compatible Ikelite DS strobes
-ABS-PC construction is fundamentally corrosion-resistant

In the Box

Housing
Rear O-ring # 0132.59 (installed)
Front O-ring # 0132.45 (installed)
Zoom Gear Retainer # 75900 (installed)
Port Hole Cover # 0200.92 (installed)
Waterproof Bulkhead Cap # 9104.7 (installed)
Base with Left-Hand Quick Release Handle # 4077.67 (installed)
Camera Mount for Sony a7S III # 95415
Camera Mount for Sony a1 # 95419
Tool for Zoom Gear Retainer # 0945.06
.050" Hex Key # 0945.11
Silicone Lubricant 1cc Tube